Materials (Basel, Switzerland)

journal of clinical medicine

advances in colloid and interface science

zhongguo dang dai er ke za zhi = chinese journal of contemporary pediatrics

[1] Human saliva and model saliva at bulk to adsorbed phases - similarities and differences.

[2] direct acetylation of sunflower oil in the presence of boron trioxide catalyst and the adduct usage as the base stock and lubricant additive

[3] effects of compression speed and lubrication on the compaction properties of some commonly used direct compression materials

[4] ionanocarbon lubricants. the combination of ionic liquids and carbon nanophases in tribology

[5] Numerical simulation of wire-coating low-density polyethylene: Theory and experiments

[6] Analysis on cooling and lubrication mechanism of high-pressure cutting fluid for vermicular cast iron cutting based on AdvantEdge

[7] Analysis on cooling and lubrication mechanism of high-pressure cutting fluid for vermicular cast iron cutting based on AdvantEdge

[8] Tribological properties of chemical vapor deposited diamond film on YT14 cemented carbide under water lubrication condition

[9] Adaptive control in lubrication, adhesion, and hemostasis by Chitosan-Catechol-pNIPAM.

[10] Effect of CNTs in Copper Matrix on Mechanical Characteristics and Tribological Behavior under Dry Sliding and Boundary Lubrication Conditions.

[11] Boundary and Elastohydrodynamic Lubrication Behaviors of Nano-CuO/Reduced Graphene Oxide Nanocomposite as an Efficient Oil-Based Additive.

[12] Research on the lubrication performance of engine piston skirt–cylinder liner frictional pair considering lubricating oil transport

[13] Lubrication analysis of piston skirt-cylinder liner frictional pair considering transport status of lubricating oil

[14] On the lubrication performance of external gear pumps for aerospace fuel delivery applications

[15] Wear Performance Analysis of Ni⁻Al₂O₃ Nanocomposite Coatings under Nonconventional Lubrication.

[16] Biolubrication synergy: Hyaluronan - Phospholipid interactions at interfaces.

[17] Effect of Lubrication on Sliding Wear of Red Mud Particulate Reinforced Aluminium Alloy 6061

[18] Optimization of Nanofluid Minimum Quantity Lubrication (NanoMQL) Technique for Grinding Performance Using Jaya Algorithm

[19] The effect of the electrical double layer on hydrodynamic lubrication: a non-monotonic trend with increasing zeta potential

[20] Energy conservation and environmental sustainability during grinding operation of Ti–6Al–4V alloys via eco-friendly oil/graphene nano additive and Minimum quantity lubrication

[21] Characteristics Study of In-Situ Capacitive Sensor for Monitoring Lubrication Oil Debris

[22] tribological analysis of mg2si particulates reinforced powder metallurgy magnesium alloy composites under oil lubrication condition

[23] investigation of flow behavior in minimum quantity lubrication nozzle for end milling processes

[24] effect of workpiece orientation, lubrication and media geometry on the effectiveness of vibratory finishing of al6061

[25] investigation on the use of palm olein as lubrication oil

[26] effects of compression speed and lubrication on the compaction properties of some commonly used direct compression materials

[27] engineering software solution for thermal elastohydrodynamic lubrication using multiphysics software

[28] effect of surface texturing parameters on the lubrication characteristics of an axial piston pump valve plate

[29] experimental investigations of biological lubrication at the nanoscale: the cases of synovial joints and the oral cavity

[30] mixed lubrication effects in the lateral lubricating interfaces of external gear machines: modelling and experimental validation

[31] influence of slip and lubrication regime on the formation of white etching cracks on a two-disc test rig

[32] micro-lubrication of directionally oriented contact surfaces

[33] controllable sliding bearings and controllable lubrication principles—an overview

[34] Calendering of Pseudoplastic and Viscoplastic Fluids Using the Lubrication Approximation

[35] Calendering analysis without the lubrication approximation