Comparison of two different types of railway ballast in compression and direct shear tests: experimental results and DEM model validation.

Clicks: 313
ID: 21299
2018
Article Quality & Performance Metrics
Overall Quality
Not rated
Combines reader engagement with the AI quality analysis. This article has not been analysed, so there is no overall score — reader engagement is measured and shown alongside.
AI Quality Assessment
Not analyzed
Readership in this journal
Star

Ranked #2 of 3 articles by views in granular matter

Most read Least read

Bar heights use a square-root scale.

Mint this article as an NFT
Not yet minted

Create a permanent, verifiable on-chain record of this article on the Scimatic Network. The NFT is held in your Journament account, and you can withdraw it to your own wallet at any time.

5 SUSD one-off · no wallet required
Abstract
Railway ballast is an angular and coarse material, which demands careful DEM modelling and validation. Particle shape is often modelled in high accuracy, thus leading to computational expensive DEM models. Whether this effort will increase the DEM model's overall prediction quality will also vitally depend on the used contact law and the validation process. In general, a DEM model validated using different types of principal experiments can be considered more trustworthy in simulating other load cases. Here, two types of railway ballast are compared and DEM model validation is conducted. Calcite and Kieselkalk are investigated under compression and direct shear test. All experimental data will be made openly accessible to promote further research on this topic. In the experiments, the behaviour of Calcite and Kieselkalk is surprisingly similar in the direct shear test, while clear differences can be seen in the stiffnesses in the compression test. In DEM modelling, simple particle shapes are combined with the Conical Damage Model contact law. For each type of ballast, one set of parameters is found, such that simulation and experimental results are in good accordance. A comparison with the simplified Hertz-Mindlin contact law shows several drawbacks of this model. First, the model cannot be calibrated to meet both compression and shear test results. Second, the similar behaviour in shear testing but differences in compression cannot be reproduced using the Hertz-Mindlin model. For these reasons, the CDM model is considered the better choice for the simulation of railway ballast, if simple particle shapes are used.
Железнодорожный балласт представляет собой остроугольный крупнозернистый материал, требующий тщательного моделирования методом дискретных элементов (МДЭ) и последующей валидации. Форма частиц зачастую воспроизводится с высокой точностью, что приводит к созданию вычислительно затратных моделей МДЭ. Приведут ли эти затраты к повышению общей предсказательной способности модели, существенно зависит от используемого закона контактного взаимодействия и процесса валидации. В целом модель МДЭ, валидированная на основе различных типов базовых экспериментов, считается более надежной при моделировании других сценариев нагружения. В настоящей работе сопоставляются два типа железнодорожного балласта и проводится валидация модели МДЭ. Исследовано поведение кальцита и кизелькалька в условиях сжатия и прямого сдвига. Все экспериментальные данные будут предоставлены в открытом доступе для стимулирования дальнейших исследований по данной теме. В ходе экспериментов поведение кальцита и кизелькалька оказалось неожиданно схожим при испытаниях на прямой сдвиг, в то время как при сжатии наблюдались отчетливые различия в жесткости. В МДЭ-моделировании простые формы частиц комбинируются с контактным законом конической модели повреждаемости (Conical Damage Model, CDM). Для каждого типа балласта был определен единый набор параметров, обеспечивающий хорошее согласование результатов моделирования и экспериментальных данных. Сравнение с упрощенным контактным законом Герца — Миндлина выявило ряд недостатков последнего. Во-первых, данную модель невозможно откалибровать таким образом, чтобы одновременно удовлетворить результатам испытаний как на сжатие, так и на сдвиг. Во-вторых, модель Герца — Миндлина не позволяет воспроизвести схожее поведение материалов при сдвиге при наличии различий при сжатии. По этим причинам модель CDM признана более предпочтительным решением для моделирования железнодорожного балласта в случае использования частиц простой формы.
Reference Key
suhr2018comparisongranular Use this key to autocite in the manuscript while using SciMatic Manuscript Manager or Thesis Manager
Authors
Journal granular matter
Year 2018
DOI
10.1007/s10035-018-0843-9
URL
Keywords Keywords not found

Citations

No citations found. To add a citation, contact the admin at info@scimatic.org

No comments yet. Be the first to comment on this article.