spray-dried tomato powder: reconstitution properties and colour
Clicks: 257
ID: 198059
2008
Article Quality & Performance Metrics
Overall Quality
Not rated
Combines reader engagement with the AI quality analysis. This
article has not been analysed, so there is no overall score —
reader engagement is measured and shown alongside.
Reader Engagement
Steady Performance
30.0
/100
257 views
26 readers
AI Quality Assessment
Not analyzed
Readership in this journal
SteadyRanked #53 of 150 articles by views in current drug delivery
Most read
Least read
Bar heights use a square-root scale. Only the 120 most-read articles are drawn; the journal has 150 in total.
Mint this article as an NFT
Not yet mintedCreate a permanent, verifiable on-chain record of this article on the Scimatic Network. The NFT is held in your Journament account, and you can withdraw it to your own wallet at any time.
5
SUSD
one-off · no wallet required
Abstract
Powdered tomato was produced by spray drying the tomato pulp. A full 2³ factorial design with the central point was used, varying the feed flow rate (127-276 g/min), air inlet temperature (200-220ºC) and the atomisation speed (25,000-35,000 rpm). The responses analysed were: moisture content, solubility, wettability consistency and colour, but the factors only significantly affected the colour parameter. All the samples became significantly darker and less red with an increase of the variables under study. A low atomisation speed (25,000 rpm) and lower inlet air temperature (220ºC) produced the powders with a higher colour index (a/b) and less darkening.
Tomate em pó foi produzido por secagem por atomização da polpa de tomate. Um planejamento 2³fatorial completo com ponto central foi conduzido variando a taxa de alimentação (127276 g/min), temperatura de entrada do ar (200-220ºC) e a velocidade de atomização (25000-35000 rpm). As respostas analisadas foram: conteúdo de umidade, solubilidade, molhabilidade, consistência e cor, ma os fatores somente afetaram significativamente a cor. Todas as amostras tornaram significantemente mais escuras e menos vermelhas com o aumento das variáveis sob estudo. Baixa velocidade de atomização (25000 rpm) e menor temperatura do ar de secagem (220ºC) produziram pós de maior índice de cor (a/b) e menor escurecimento.
Tomate em pó foi produzido por secagem por atomização da polpa de tomate. Um planejamento 2³fatorial completo com ponto central foi conduzido variando a taxa de alimentação (127276 g/min), temperatura de entrada do ar (200-220ºC) e a velocidade de atomização (25000-35000 rpm). As respostas analisadas foram: conteúdo de umidade, solubilidade, molhabilidade, consistência e cor, ma os fatores somente afetaram significativamente a cor. Todas as amostras tornaram significantemente mais escuras e menos vermelhas com o aumento das variáveis sob estudo. Baixa velocidade de atomização (25000 rpm) e menor temperatura do ar de secagem (220ºC) produziram pós de maior índice de cor (a/b) e menor escurecimento.
| Reference Key |
sousa2008brazilianspray-dried
Use this key to autocite in the manuscript while using
SciMatic Manuscript Manager or Thesis Manager
|
|---|---|
| Authors | ;Alexandre Santos de Sousa;Soraia Vilela Borges;Natália Ferreira Magalhães;Hevandro Vaz Ricardo;Aline Damico Azevedo |
| Journal | current drug delivery |
| Year | 2008 |
| DOI |
10.1590/S1516-89132008000400019
|
| URL | |
| Keywords |
Citations
No citations found. To add a citation, contact the admin at info@scimatic.org
Comments
No comments yet. Be the first to comment on this article.